The i.MX8M Plus DHCOM based boards have compatible string in the form:
"vendor,custom-board", "dh,som", "fsl,soc"
or
"dh,carrier-board", "dh,som", "fsl,soc"
Split the binding entry so this triplet can be matched on.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The NITROGEN SoM based boards have compatible string in the form:
"vendor,custom-board", "boundary,som", "fsl,soc"
Split the binding entry so this triplet can be matched on.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MX8Menlo board is based on i.MX8M Mini Toradex Verdin SoM
which results in compatible string in the form:
"vendor,custom-board", "toradex,som-nonwifi", "toradex,som", "fsl,soc"
Move the binding entry so this quadruplet can be matched on.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add an entry for the Starterkit SK-iMX53 development board.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add entries to the list of imx8mp boards denoting the Debix Model A
board from Polyhex Technology Co, along with a more generic entry that
can be used where both the Model A and Model B are supported.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Core changes:
- Minor but nice and important documentation clean-ups.
New drivers:
- New subdriver for the Qualcomm SDM670 SoC.
- New subdriver for the Intel Moorefield SoC.
- New trivial support for the NXP Freescale i.MXRT1170 SoC.
Other changes and improvements
- A major clean-up of the Qualcomm pin control device tree bindings
by Krzysztof.
- A major header clean-up by Andy.
- Some immutable irqchip clean-up for the Actions Semiconductor
and Nuvoton drivers.
- GPIO helpers for The Cypress cy8c95x0 driver.
- Bias handling in the Mediatek MT7986 driver.
- Remove the unused pins-are-numbered concept that never flew.
-----BEGIN PGP SIGNATURE-----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=PhTP
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"The two large chunks is the header clean-up from Andy and the Qualcomm
DT bindings clean-up from Krzysztof. Each which could give rise to
conflicts, but I haven't seen any.
The YAML conversions happening around the device tree is the biggest
item in the series and is the result of Rob Herrings ambition to
autovalidate these trees against strict schemas and it is paying off
in lots of bugs found and ever prettier device trees. Sooner or later
the transition will be complete, Krzysztof is fixing up all of the
Qualcomm stuff, which is pretty voluminous.
Core changes:
- minor but nice and important documentation clean-ups
New drivers:
- subdriver for the Qualcomm SDM670 SoC
- subdriver for the Intel Moorefield SoC
- trivial support for the NXP Freescale i.MXRT1170 SoC
Other changes and improvements
- major clean-up of the Qualcomm pin control device tree bindings by
Krzysztof
- major header clean-up by Andy
- some immutable irqchip clean-up for the Actions Semiconductor and
Nuvoton drivers
- GPIO helpers for The Cypress cy8c95x0 driver
- bias handling in the Mediatek MT7986 driver
- remove the unused pins-are-numbered concept that never flew"
* tag 'pinctrl-v6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (231 commits)
pinctrl: thunderbay: fix possible memory leak in thunderbay_build_functions()
dt-bindings: pinctrl: st,stm32: Deprecate pins-are-numbered
dt-bindings: pinctrl: mediatek,mt65xx: Deprecate pins-are-numbered
pinctrl: stm32: Remove check for pins-are-numbered
pinctrl: mediatek: common: Remove check for pins-are-numbered
pinctrl: qcom: remove duplicate included header files
pinctrl: sunxi: d1: Add CAN bus pinmuxes
pinctrl: loongson2: Fix some const correctness
pinctrl: pinconf-generic: add missing of_node_put()
pinctrl: intel: Enumerate PWM device when community has a capability
pwm: lpss: Rename pwm_lpss_probe() --> devm_pwm_lpss_probe()
pwm: lpss: Allow other drivers to enable PWM LPSS
pwm: lpss: Include headers we are the direct user of
pwm: lpss: Rename MAX_PWMS --> LPSS_MAX_PWMS
pwm: Add a stub for devm_pwmchip_add()
pinctrl: k210: call of_node_put()
pinctrl: starfive: Use existing variable gpio
dt-bindings: pinctrl: semtech,sx150xq: fix match patterns for 16 GPIOs matching
pinconf-generic: fix style issues in pin_config_param doc
pinctrl: pinctrl-loongson2: fix Kconfig dependency
...
Recently the imxrt1050 was added but the cpu compatible node wasn't
added. Add both i.MXRT1170 and 1050 compatibles to fsl.yaml.
Cc: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221107071511.2764628-2-Mr.Bossman075@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a compatible string for the Kobo Aura 2 eBook reader.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DT core:
- Fix node refcounting in of_find_last_cache_level()
- Constify device_node in of_device_compatible_match()
- Fix 'dma-ranges' handling in bus controller nodes
- Fix handling of initrd start > end
- Improve error reporting in of_irq_init()
- Taint kernel on DT unittest running
- Use strscpy instead of strlcpy
- Add a build target, dt_compatible_check, to check for
compatible strings used in kernel sources against compatible strings
in DT schemas.
- Handle DT_SCHEMA_FILES changes when rebuilding
DT bindings:
- LED bindings for MT6370 PMIC
- Convert Mediatek mtk-gce mailbox, MIPS CPU interrupt controller,
mt7621 I2C, virtio,pci-iommu, nxp,tda998x, QCom fastrpc, qcom,pdc,
and arm,versatile-sysreg to DT schema format
- Add nvmem cells to u-boot,env schema
- Add more LED_COLOR_ID definitions
- Require 'opp-table' uses to be a node
- Various schema fixes to match QEMU 'virt' DT usage
- Tree wide dropping of redundant 'Device Tree Binding' in schema titles
- More (unevaluated|additional)Properties fixes in schema child nodes
- Drop various redundant minItems equal to maxItems
-----BEGIN PGP SIGNATURE-----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=IDIz
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DT core:
- Fix node refcounting in of_find_last_cache_level()
- Constify device_node in of_device_compatible_match()
- Fix 'dma-ranges' handling in bus controller nodes
- Fix handling of initrd start > end
- Improve error reporting in of_irq_init()
- Taint kernel on DT unittest running
- Use strscpy instead of strlcpy
- Add a build target, dt_compatible_check, to check for compatible
strings used in kernel sources against compatible strings in DT
schemas.
- Handle DT_SCHEMA_FILES changes when rebuilding
DT bindings:
- LED bindings for MT6370 PMIC
- Convert Mediatek mtk-gce mailbox, MIPS CPU interrupt controller,
mt7621 I2C, virtio,pci-iommu, nxp,tda998x, QCom fastrpc, qcom,pdc,
and arm,versatile-sysreg to DT schema format
- Add nvmem cells to u-boot,env schema
- Add more LED_COLOR_ID definitions
- Require 'opp-table' uses to be a node
- Various schema fixes to match QEMU 'virt' DT usage
- Tree wide dropping of redundant 'Device Tree Binding' in schema
titles
- More (unevaluated|additional)Properties fixes in schema child nodes
- Drop various redundant minItems equal to maxItems"
* tag 'devicetree-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (62 commits)
of: base: Shift refcount decrement in of_find_last_cache_level()
dt-bindings: leds: Add MediaTek MT6370 flashlight
dt-bindings: leds: mt6370: Add MediaTek MT6370 current sink type LED indicator
dt-bindings: mailbox: Convert mtk-gce to DT schema
of: base: make of_device_compatible_match() accept const device node
of: Fix "dma-ranges" handling for bus controllers
of: fdt: Remove unused struct fdt_scan_status
dt-bindings: display: st,stm32-dsi: Handle data-lanes in DSI port node
dt-bindings: timer: Add power-domains for TI timer-dm on K3
dt: Add a check for undocumented compatible strings in kernel
kbuild: take into account DT_SCHEMA_FILES changes while checking dtbs
dt-bindings: interrupt-controller: migrate MIPS CPU interrupt controller text bindings to YAML
dt-bindings: i2c: migrate mt7621 text bindings to YAML
dt-bindings: power: gpcv2: correct patternProperties
dt-bindings: virtio: Convert virtio,pci-iommu to DT schema
dt-bindings: timer: arm,arch_timer: Allow dual compatible string
dt-bindings: arm: cpus: Add kryo240 compatible
dt-bindings: display: bridge: nxp,tda998x: Convert to json-schema
dt-bindings: nvmem: u-boot,env: add basic NVMEM cells
dt-bindings: remoteproc: qcom,adsp: enforce smd-edge schema
...
i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT compatible string for i.MX8M Mini based Gateworks GW7904 board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT compatible strings for a combination of the 14N0600E variant of
the Avnet (MSC branded) SM2S-IMX8PLUS SoM on it's own and in combination
with the SM2-MB-EP1 carrier board.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This updates the bindings in order to use names for the boards that
follow the latest convention used by Kontron marketing.
By updating we make sure, that we can maintain this more easily in
future and make sure that the proper devicetree can be selected for
the hardware.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This updates the bindings in order to simplify the devicetree
structure and to add names for the boards that follow the latest
convention used by Kontron marketing.
It also gets rid of the N6xxx notation in the compatibles and
file names, as they are not really used anymore and often result
in confusion.
This is a breaking change, but the impact shouldn't be too big
and it makes usage and maintenance easier in the future.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TQMa8MPxL is a SOM family using NXP i.MX8MP CPU family
MBa8MPxL is an evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mp-<SOM>" for the module and
"tq,imx8mp-<SOM>-<SBC>"
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add binding for the Ixora V1.2 carrier board our Apalis iMX6D/Q
may be mated with.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Decrease the line length of the toradex colibri boards to fix the
following build warning:
./Documentation/devicetree/bindings/arm/fsl.yaml:684:111: [warning]
line too long (111 > 110 characters) (line-length)
The description already contains the SoM name, do not repeat it
in every single line.
Reported-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT compatible string for DH electronics i.MX8M Plus DHCOM and PDK2
into YAML DT binding document. This system is a general purpose SoM and
evaluation board.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: devicetree@vger.kernel.org
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Based on toradex,colibri-imx7s, toradex,colibri-imx7d and
toradex,colibri-imx7d-emmc module device trees add iris and iris-v2 for
carrier board dts.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the board imx93-11x11-evk in the binding docuemnt.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree binding for the Bosch ACC board, based on i.MX6 Dual.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive Evaluation
Board from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add bindings for it.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the board ls1021a-iot in the binding docuemnt.
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT compatible string for board based on the Toradex Verdin iMX8M
Mini SoM, the MX8Menlo. The board is a compatible replacement for
i.MX53 M53Menlo and features USB, multiple UARTs, ethernet, LEDs,
SD and eMMC.
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: devicetree@vger.kernel.org
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This eval board features an IMX8MN UltraLite and has DDR3L RAM. The
product part number is 8MNANOD3L-EVK.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bindings for Aster, Iris and Iris V2 carrier boards our
Colibri iMX6S/DL may be mated with.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The dedicated device tree for V1.1 modules has been dropped. Remove
its bindings too.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add toradex,verdin-imx8mp for the Verdin iMX8M Plus modules, its nonwifi
and wifi variants and the carrier boards (both Dahlia and the Verdin
Development Board) they may be mated in.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add comment regarding the i.MX53 based Menlo board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: devicetree@vger.kernel.org
To: linux-arm-kernel@lists.infradead.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TQMa6ULx is a SOM family using NXP i.MX6UL CPU family.
TQMa6ULLx is a SOM family using NXP i.MX6ULL CPU family.
Both are available as a socket type as well as an LGA type.
For both variants there are the mainboards MBa6ULx and MBa6ULxL, trailing
'L' is LGA version.
Finally there is the possibility to use the socket module with an LGA
adapter on the MBa6ULxL.
The SOM needs a mainboard, therefore we provide compatibles using this
naming schema:
"tq,imx6ul-<SOM>" for the module and
"tq,imx6ul-<SOM>-<SBC>" for when mounted on the mainboard.
The i.MX6ULL version is done similar.
Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT compatible string for Data Modul i.MX8M Mini eDM SBC board
into YAML DT binding document. This system is an evaluation board
for various custom display units.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: devicetree@vger.kernel.org
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD connector with UHS support
- LIS2DE12 3-axis accelerometer
- Gateworks System Controller
- IMX8M FEC
- software selectable RS232/RS485/RS422 serial transceiver
- PMIC
- 2x off-board bi-directional opto-isolated digital I/O
- 1x M.2 A-E Key Socket and 1x MiniPCIe socket with USB2.0 and PCIe
(resistor loading to route PCIe/USB2 between M.2 and MiniPCIe socket)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add toradex,verdin-imx8mm for our new Verdin iMX8M Mini modules, its
nonwifi and wifi variants and the carrier boards (both Dahlia and the
Verdin Development Board) they may be mated in.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch presents the yaml patch for the emtrion GmbH
emCON-MX8M Mini.
Signed-off-by: Reinhold Mueller <reinhold.mueller@emtrion.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the compatible string for the Protonic PRT8MM board, which is a
reference design for a low-cost agricultural terminal.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TQMa8Mx is a SOM family using NXP i.MX8M[Q,QL, D] CPU
MBa8Mx is a evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mq-<SOM>" for the module and
"tq,imx8mq-<SOM>-<SBC>" for the module on that mainboard
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TQMa8MxNL is a SOM family using NXP i.MX8MN[Q,QL,DL,S,SL] CPU
MBa8Mx is an evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mn-<SOM>" for the module and
"tq,imx8mn-<SOM>-<SBC>" for mainboards
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TQMa8MxML is a SOM family using NXP i.MX8MM[Q,QL,DL,S,SL] CPU
MBa8Mx is an evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mm-<SOM>" for the module and
"tq,imx8mm-<SOM>-<SBC>" for the module on that mainboard
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the dt binding for i.MX8ULP EVK board.
i.MX 8ULP is part of the ULP family with emphasis on extreme
low-power techniques using the 28 nm fully depleted silicon on
insulator process. Like i.MX 7ULP, i.MX 8ULP continues to be
based on asymmetric architecture, however will add a third DSP
domain for advanced voice/audio capability and a Graphics domain
where it is possible to access graphics resources from the
application side or the realtime side.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add devicetree binding for Crux/Crux+ boards from the IOTA family.
These boards have the very same HW configuration as the Orion board
except the usage of Quad/QuadPlus SoC.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The TQ-Systems MBa6x mainboard can be used with TQMa6 variants with
i.MX6Q/QP/DL SoCs (TQMa6Q/QP/DL). The TQMa6Q and DL exist in two variants:
The newer variants "A" have a hardware workaround for Erratum ERR006687,
while variants "B" are missing such a workaround, so it needs to be
handled in software. The erratum was fixed in i.MX6QP, so no "A" variant
of the TQMa6QP exists.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the missing board in the binding docuemnt.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add toradex,colibri-imx6ull-emmc for our new Colibri iMX6ULL 1GB (eMMC)
Module and the carrier boards (so far only Colibri Evaluation Board) it
may be mated in.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document the compatible string for the LX2160A system that is part of
the BlueBox 3. Also add a separate compatible string for Rev A, since
technically it uses a different device tree.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document the compatible for the Ten64 board which will
be included as freescale/fsl-ls1088a-ten64.dtb in arm64.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DH electronics DHCOM PicoITX and DHCOM DRC02 boards. The DHCOM DRC02
device can only house a SOM with iMX6S and not with iMX6DL, due to some
thermal design consideration. But for compatible fsl,imx6dl is chosen,
because fsl,imx6s isn't available, the iMX6S is basically a iMX6DL with
one CPU core disabled and therefore the kernel discerns the iMX6S/iMX6DL
automatically.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: robh+dt@kernel.org
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: kernel@dh-electronics.com
Cc: Fabio Estevam <festevam@denx.de>
To: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add compatible for the MNT Reform2 laptop board.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add compatible for the BoundaryDevices Nitrogen8 system on module.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document the compatible for GE B1x5pv2 boards.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
- i.MX8M Mini SoC
- LPDDR4 DRAM
- eMMC FLASH
- SPI FRAM
- Gateworks System Controller (GSC)
- Atmel ATECC Crypto Authentication
- USB 2.0
- Microchip GbE Switch
- Multiple multi-protocol RS232/RS485/RS422 Serial ports
- onboard 802.11ac WiFi / BT
- microSD socket
- miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
- Wide range DC power input
- 802.3at PoE
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive Evaluation
Board from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Add bindings for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
i.Core MX8M Mini needs to mount on top of this Carrier board for
creating complete i.Core MX8M Mini C.TOUCH 2.0 board.
Add bindings for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Nitrogen8M Mini is an ARM based single board computer (SBC).
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add an entry for the Librem 5 phone, Evergreen revision which is supported
by "r4". Schematics and more information can be found at
https://developer.puri.sm/Librem5/Hardware_Reference/Evergreen.html
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the a new variant for the Kontron SMARC-sAL28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bindings for the Gateworks Venice Development kit boards with
IMX8MM System on Module.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Plymovent Group BV BAS iMX6dl based board
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add beacon,imx8mn-beacon-kit to list of compatible options.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Quite some patches that update vendor-prefixes.yaml and fsl.yaml to
document missing board compatibles and add new board compatibles.
- A couple of patches from Dong Aisheng to update imx-scu firmware and
imx-lpcg clock bindings for new SCU two cells clock support.
- A couple of net bindings update from Ioana Ciornei to complete the
MAC/PCS/PHY representation on DPAA2 devices.
- Document watchdog compatibles for all i.MX and Layerscape devices.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl/HlOYUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4yegf/eP6henuph6c+Ay/y7Ia4V51UY4ot
Sb9pJatgaX4GmFowfztltd//gJMtpHnYbqAsXhk2hkRZ7h0hFIIji2Dp7knq3naD
rQykAmT4eWy1CuQFq86XvFaqHc5AVuygBpMmP6nSFDBzBeqDRQ+q813aUpQdUlUH
iAeN2Ov62U+4kEc0AxF2mNNcGW1/ikKcFT5nJmJGmgUKuwSUSJ0l09MvXHhQeEjr
//gswg/5XU4tweEjAHeEJKM60XLtRFdmoLnz/0nDlLY0BXfBYRpicvNXzxDWEPOd
qdf20NOWyz2UUcmMgy1vpVJKHQumSDNxB9M0FwtkcB8+x0YjE4gB8AxUNA==
=YiM1
-----END PGP SIGNATURE-----
Merge tag 'imx-bindings-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX DT bindings update for 5.11:
- Quite some patches that update vendor-prefixes.yaml and fsl.yaml to
document missing board compatibles and add new board compatibles.
- A couple of patches from Dong Aisheng to update imx-scu firmware and
imx-lpcg clock bindings for new SCU two cells clock support.
- A couple of net bindings update from Ioana Ciornei to complete the
MAC/PCS/PHY representation on DPAA2 devices.
- Document watchdog compatibles for all i.MX and Layerscape devices.
* tag 'imx-bindings-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (35 commits)
dt-bindings: arm: fsl: add Protonic WD3 board
dt-bindings: vendor-prefixes: add "virtual" prefix
dt-bindings: fsl: add kamstrup flex concentrator to schema
dt-bindings: arm: fsl: document i.MX7S boards
dt-bindings: arm: fsl: document SolidRun LX2160A boards
dt-bindings: arm: fsl: document LS1012A FRWY board
dt-bindings: arm: fsl: add Van der Laan LANMCU board
dt-bindings: arm: fsl: add Altesco I6P board
dt-bindings: vendor-prefixes: Add an entry for Altus-Escon-Company
dt-bindings: net: add the 10gbase-r connection type
dt-bindings: net: add the DPAA2 MAC DTS definition
dt-bindings: fsl: add compatible for LX2162A QDS Board
dt-bindings: vendor-prefixes: Add an entry for Van der Laan b.v.
dt-bindings: arm: fsl: document i.MX7D boards
dt-bindings: arm: fsl: document i.MX6ULL boards
dt-bindings: arm: fsl: document i.MX6UL boards
dt-bindings: arm: fsl: document i.MX6SX boards
dt-bindings: arm: fsl: document i.MX6SL boards
dt-bindings: arm: fsl: document i.MX6QP boards
dt-bindings: arm: fsl: document i.MX6Q boards
...
Link: https://lore.kernel.org/r/20201202142717.9262-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add Kamstrup OMNIA Flex Concentrator compatibles to the schema
so we can make use of them for the validation.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX7S based boards.
The Toradex boards use multiple compatibles.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document the compatible for SolidRun LX2160A based boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document the compatible for LS1012A FRWY board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Van der Laan LANMCU iMX6dl based board
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for LX2162A, LX2162A is LX2160A based SoC.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX7D based boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX6ULL based boards.
The Armadeus boards use multiple compatibles.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX6UL based boards.
The Armadeus boards use multiple compatibles.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX6SX based boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX6SL based boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX6QP based boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX6Q based boards.
The Toradex and the Armadeus boards use multiple compatibles.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add entries for the SoMs and boards based on i.MX8MM from Kontron
Electronics GmbH.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX6DL based Aristainetos
boards from ABB.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX6DL based boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for VF500 and VF600 based boards.
The Toradex Colibri Evaluation Boards use multiple compatibles.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX53 based boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX51 based boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document and adjust the compatibles for i.MX25 and i.MX27 based boards
to fix dtbs_check warnings like:
arch/arm/boot/dts/imx27-apf27dev.dt.yaml: /: compatible:
['armadeus,imx27-apf27dev', 'armadeus,imx27-apf27', 'fsl,imx27'] is not valid under any of the given schemas
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to add meta-schema checks for additional/unevaluatedProperties
being present, all schema need to make this explicit. As the top-level
board/SoC schemas always have additional properties, add
'additionalProperties: true'.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201005183830.486085-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Add a binding for the Variscite Symphony evaluation kit board with
VAR-SOM-MX8MN System on Module.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add devicetree bindings for i.MX6 based phyCORE-i.MX6, phyBOARD-Mira and
phyFLEX-i.MX6.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add devicetree bindings for i.MX6 UL/ULL based phyCORE-i.MX6 UL/ULL and
phyBOARD-Segin.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All Purism Librem5 phones have three compatibles so they need their own
entry to fix dbts_check warnings like:
arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dt.yaml: /:
compatible: ['purism,librem5r2', 'purism,librem5', 'fsl,imx8mq'] is not valid under any of the given schemas
arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dt.yaml: /:
compatible: ['purism,librem5r2', 'purism,librem5', 'fsl,imx8mq'] is too long
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add entry for i.MX8MM DDR4 EVK board and update
the comments for imx8mm-evk as it is populated
with LPDDR4.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a compatible string for the Tolino Shine 2 HD eBook reader.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a binding for the Variscite Symphony evaluation kit board with
VAR-SOM-MX8MM System on Module.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a binding for the Variscite VAR-SOM-MX8MM System on Module.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Toradex Colibri i.MX 8 Evaluation board has two Toradex compatibles
so it needs separate entry. This fixes dtbs_check warning:
arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dt.yaml: /:
compatible: ['toradex,colibri-imx8x-eval-v3', 'toradex,colibri-imx8x', 'fsl,imx8qxp'] is not valid under any of the given schemas (Possible causes of the failure):
arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dt.yaml: /: compatible: ['toradex,colibri-imx8x-eval-v3', 'toradex,colibri-imx8x', 'fsl,imx8qxp'] is too long
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document the binding for Beacon EmbeddedWorks i.MX8M Mini Development
Kit board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add entries for the imx8mq based Librem 5 phone. The "Birch" and
"Chestnut" hardware revisions are supported by r2. The "Dogwood"
revision by r3.
See https://puri.sm/products/librem-5/ and https://developer.puri.sm/Librem5/
for the schematics and more information.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add devicetree binding for Orion - new board variant in the Y Soft
IOTA family.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Kontron SMARC module compatibles to the schema so we can make use of
them for the validation.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most of the commits are for additional hardware support and minor fixes
for existing machines for all the usual platforms: qcom, amlogic, at91,
gemini, mediatek, ti, socfpga, i.mx, layerscape, uniphier, rockchip,
exynos, ux500, mvebu, tegra, stm32, renesas, sunxi, broadcom, omap,
and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation.
Andre Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into
dts files, for many devices that relied on a mix of auxiliary data
in addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants, along
with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based on
the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=ye2F
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
APF6 Dev compatible is armadeus,imx6dl-apf6dev and not
armadeus,imx6dl-apf6dldev.
Fixes: 3d735471d0 ("dt-bindings: arm: Document Armadeus SoM and Dev boards devicetree binding")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add the Kontron SMARC-sAL28 board, its variants and combination with
carriers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The $id path checks were inadequately checking the path part of the $id
value. With the check fixed, there's a number of errors that need to be
fixed. Most of the errors are including 'bindings/' in the path which
should not be as that is considered the root.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "Nuno Sá" <nuno.sa@analog.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Stefan Popa <stefan.popa@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Marcus Folkesson <marcus.folkesson@gmail.com>
Cc: Kent Gustavsson <kent@minoris.se>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-iio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add the compatible enum entries for Gateworks Ventana boards.
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add devicetree binding for Thor96 Board from Einfochips. This board is
one of the 96Boards Consumer Edition platform powered by NXP i.MX8MQ SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Google Coral Edge TPU, named as imx8mq-phanbell, to the
imx8mq supported devices.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The lx2160a board compatibles "fsl,lx2160a-qds" and "fsl,lx2160a-rdb"
have been in use. Let's document them.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add an entry for the Embedded Artists i.MX7ULP COM board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a compatible string for the Tolino Shine 3 eBook reader.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the compatibles for Kontron i.MX6UL N6311 SoM and boards and
the compatibles for Kontron i.MX6ULL N6411 SoM and boards.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a compatible string for the Kobo Clara HD eBook reader.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
