mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
synced 2025-09-11 10:43:16 +00:00
arm64: dts: qcom: sc8180x: Add pmics
SC8180X based platforms have PM8150, PM8150C, PMC8180 and SMB2351 PMICs, so add these as well Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230530162454.51708-14-vkoul@kernel.org
This commit is contained in:
Vinod Koul
Bjorn Andersson
parent
494dec9b6f
commit
d3302290f5
326
arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi
Normal file
326
arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi
Normal file
@ -0,0 +1,326 @@
|
||||
// SPDX-License-Identifier: BSD-3-Clause
|
||||
/*
|
||||
* Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
|
||||
* Copyright (c) 2021-2023, Linaro Limited
|
||||
*/
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
#include <dt-bindings/spmi/spmi.h>
|
||||
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
||||
|
||||
/ {
|
||||
thermal-zones {
|
||||
pmc8180-thermal {
|
||||
polling-delay-passive = <100>;
|
||||
polling-delay = <0>;
|
||||
|
||||
thermal-sensors = <&pmc8180_temp>;
|
||||
|
||||
trips {
|
||||
trip0 {
|
||||
temperature = <95000>;
|
||||
hysteresis = <0>;
|
||||
type = "passive";
|
||||
};
|
||||
|
||||
trip1 {
|
||||
temperature = <115000>;
|
||||
hysteresis = <0>;
|
||||
type = "hot";
|
||||
};
|
||||
|
||||
trip2 {
|
||||
temperature = <145000>;
|
||||
hysteresis = <0>;
|
||||
type = "critical";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
pmc8180c-thermal {
|
||||
polling-delay-passive = <100>;
|
||||
polling-delay = <0>;
|
||||
|
||||
thermal-sensors = <&pmc8180c_temp>;
|
||||
|
||||
trips {
|
||||
trip0 {
|
||||
temperature = <95000>;
|
||||
hysteresis = <0>;
|
||||
type = "passive";
|
||||
};
|
||||
|
||||
trip1 {
|
||||
temperature = <115000>;
|
||||
hysteresis = <0>;
|
||||
type = "hot";
|
||||
};
|
||||
|
||||
trip2 {
|
||||
temperature = <145000>;
|
||||
hysteresis = <0>;
|
||||
type = "critical";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spmi_bus {
|
||||
pmc8180_0: pmic@0 {
|
||||
compatible = "qcom,pm8150", "qcom,spmi-pmic";
|
||||
reg = <0x0 SPMI_USID>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
pon: power-on@800 {
|
||||
compatible = "qcom,pm8916-pon";
|
||||
reg = <0x0800>;
|
||||
pwrkey {
|
||||
compatible = "qcom,pm8941-pwrkey";
|
||||
interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
|
||||
debounce = <15625>;
|
||||
bias-pull-up;
|
||||
linux,code = <KEY_POWER>;
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
pmc8180_temp: temp-alarm@2400 {
|
||||
compatible = "qcom,spmi-temp-alarm";
|
||||
reg = <0x2400>;
|
||||
interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
|
||||
io-channels = <&pmc8180_adc ADC5_DIE_TEMP>;
|
||||
io-channel-names = "thermal";
|
||||
#thermal-sensor-cells = <0>;
|
||||
};
|
||||
|
||||
pmc8180_adc: adc@3100 {
|
||||
compatible = "qcom,spmi-adc5";
|
||||
reg = <0x3100>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
#io-channel-cells = <1>;
|
||||
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
||||
|
||||
ref-gnd@0 {
|
||||
reg = <ADC5_REF_GND>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "ref_gnd";
|
||||
};
|
||||
|
||||
vref-1p25@1 {
|
||||
reg = <ADC5_1P25VREF>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "vref_1p25";
|
||||
};
|
||||
|
||||
die-temp@6 {
|
||||
reg = <ADC5_DIE_TEMP>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "die_temp";
|
||||
};
|
||||
};
|
||||
|
||||
pmc8180_adc_tm: adc-tm@3500 {
|
||||
compatible = "qcom,spmi-adc-tm5";
|
||||
reg = <0x3500>;
|
||||
interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
|
||||
#thermal-sensor-cells = <1>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
rtc@6000 {
|
||||
compatible = "qcom,pm8941-rtc";
|
||||
reg = <0x6000>;
|
||||
reg-names = "rtc", "alarm";
|
||||
interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
|
||||
};
|
||||
|
||||
pmc8180_gpios: gpio@c000 {
|
||||
compatible = "qcom,pmc8180-gpio";
|
||||
reg = <0xc000>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
};
|
||||
};
|
||||
|
||||
pmic@1 {
|
||||
compatible = "qcom,pmc8180", "qcom,spmi-pmic";
|
||||
reg = <0x1 SPMI_USID>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
pmic@2 {
|
||||
compatible = "qcom,smb2351", "qcom,spmi-pmic";
|
||||
reg = <0x2 SPMI_USID>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
adc@3100 {
|
||||
compatible = "qcom,spmi-adc-rev2";
|
||||
reg = <0x3100>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
#io-channel-cells = <1>;
|
||||
interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
||||
|
||||
ref-gnd@0 {
|
||||
reg = <ADC5_REF_GND>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "ref_gnd";
|
||||
};
|
||||
|
||||
vref-1p25@1 {
|
||||
reg = <ADC5_1P25VREF>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "vref_1p25";
|
||||
};
|
||||
|
||||
vcoin@85 {
|
||||
reg = <0x85>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "vcoin2";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
pmic@6 {
|
||||
compatible = "qcom,pm8150c", "qcom,spmi-pmic";
|
||||
reg = <0x6 SPMI_USID>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
pmic@8 {
|
||||
compatible = "qcom,pm8150", "qcom,spmi-pmic";
|
||||
reg = <0x8 SPMI_USID>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
pmic@a {
|
||||
compatible = "qcom,smb2351", "qcom,spmi-pmic";
|
||||
reg = <0xa SPMI_USID>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
adc@3100 {
|
||||
compatible = "qcom,spmi-adc-rev2";
|
||||
reg = <0x3100>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
#io-channel-cells = <1>;
|
||||
interrupts = <0xa 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
||||
|
||||
ref-gnd@0 {
|
||||
reg = <ADC5_REF_GND>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "ref_gnd";
|
||||
};
|
||||
|
||||
vref-1p25@1 {
|
||||
reg = <ADC5_1P25VREF>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "vref_1p25";
|
||||
};
|
||||
|
||||
vcoin@85 {
|
||||
reg = <0x85>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "vcoin";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
pmic@4 {
|
||||
compatible = "qcom,pm8150c", "qcom,spmi-pmic";
|
||||
reg = <0x4 SPMI_USID>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
power-on@800 {
|
||||
compatible = "qcom,pm8916-pon";
|
||||
reg = <0x0800>;
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
pmc8180c_temp: temp-alarm@2400 {
|
||||
compatible = "qcom,spmi-temp-alarm";
|
||||
reg = <0x2400>;
|
||||
interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
|
||||
io-channels = <&pmc8180c_adc ADC5_DIE_TEMP>;
|
||||
io-channel-names = "thermal";
|
||||
#thermal-sensor-cells = <0>;
|
||||
};
|
||||
|
||||
pmc8180c_adc: adc@3100 {
|
||||
compatible = "qcom,spmi-adc5";
|
||||
reg = <0x3100>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
#io-channel-cells = <1>;
|
||||
interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
||||
|
||||
ref-gnd@0 {
|
||||
reg = <ADC5_REF_GND>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "ref_gnd";
|
||||
};
|
||||
|
||||
vref-1p25@1 {
|
||||
reg = <ADC5_1P25VREF>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "vref_1p25";
|
||||
};
|
||||
|
||||
die-temp@6 {
|
||||
reg = <ADC5_DIE_TEMP>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
label = "die_temp";
|
||||
};
|
||||
};
|
||||
|
||||
pmc8180c_adc_tm: adc-tm@3500 {
|
||||
compatible = "qcom,spmi-adc-tm5";
|
||||
reg = <0x3500>;
|
||||
interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
|
||||
#thermal-sensor-cells = <1>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
pmc8180c_gpios: gpio@c000 {
|
||||
compatible = "qcom,pmc8180c-gpio";
|
||||
reg = <0xc000>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
};
|
||||
};
|
||||
|
||||
pmic@5 {
|
||||
compatible = "qcom,pmc8180c", "qcom,spmi-pmic";
|
||||
reg = <0x5 SPMI_USID>;
|
||||
|
||||
pmc8180c_lpg: lpg {
|
||||
compatible = "qcom,pmc8180c-lpg";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
#pwm-cells = <2>;
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
};
|
||||
Loading…
Reference in New Issue
Block a user